[Q386-Q395] 2017 Updated Lead2pass Cisco 200-125 Exam Questions

200-125 Exam Dumps Free Download In Lead2pass 100% 200-125 Exam Questions:

https://www.lead2pass.com/200-125.html

QUESTION 386
In which situation would the use of a static route be appropriate?

A.    To configure a route to the first Layer 3 device on the network segment.
B.    To configure a route from an ISP router into a corporate network.
C.    To configure a route when the administrative distance of the current routing protocol is too low.
D.    To reach a network is more than 15 hops away.
E.    To provide access to the Internet for enterprise hosts.

Answer: B

QUESTION 387 200-125 Dumps,200-125 Exam Questions,200-125 New Questions,200-125 VCE,200-125 PDF
An administrator issues the show ip interface s0/0 command and the output displays that interface Serial0/0 is up, line protocol is up What does “line protocol is up” specifically indicate about the interface?

A.    The cable is attached properly.
B.    CDP has discovered the connected device.
C.    Keepalives are being received on the interface.
D.    A carrier detect signal has been received from the connected device.
E.    IP is correctly configured on the interface.

Answer: C

QUESTION 388 200-125 Dumps,200-125 Exam Questions,200-125 New Questions,200-125 VCE,200-125 PDF
Which three statements are correct about RIP version 2? (Choose three)

A.    It uses broadcast for its routing updates
B.    It supports authentication
C.    It is a classless routing protocol
D.    It has a lower default administrative distance than RIP version 1
E.    It has the same maximum hop count as version 1
F.    It does not send the subnet mask un updates

Answer: BCE

QUESTION 389 200-125 Dumps,200-125 Exam Questions,200-125 New Questions,200-125 VCE,200-125 PDF
How can an administrator determine if a router has been configured when it is first powered up?

A.    A configured router prompts for a password.
B.    A configured router goes to the privileged mode prompt.
C.    An unconfigured router goes into the setup dialog.
D.    An unconfigured router goes to the enable mode prompt.

Answer: C

QUESTION 390 200-125 Dumps,200-125 Exam Questions,200-125 New Questions,200-125 VCE,200-125 PDF
Drag and Drop Question

3901

Answer:

3902

QUESTION 391 200-125 Dumps,200-125 Exam Questions,200-125 New Questions,200-125 VCE,200-125 PDF
Drag and Drop Question

3911

Answer:

3912

QUESTION 392 200-125 Dumps,200-125 Exam Questions,200-125 New Questions,200-125 VCE,200-125 PDF
A network administrator receives an error message while trying to configure the Ethernet interface of a router with IP address 10.24.24.24/29. Which statement explains the reason for this issue?

A.    This address is a broadcast address.
B.    VLSM-capable routing protocols must be enabled first on the router.
C.    The Ethernet interface is faulty.
D.    This address is a network address.

Answer: D

QUESTION 393 200-125 Dumps,200-125 Exam Questions,200-125 New Questions,200-125 VCE,200-125 PDF
Which address is the IPv6 all-RIP-routers multicast group address that is used by RIPng as the destination address for RIP updates?

A.    FF02::9
B.    FF02::6
C.    FF05::101
D.    FF02::A

Answer: A

QUESTION 394 200-125 Dumps,200-125 Exam Questions,200-125 New Questions,200-125 VCE,200-125 PDF
If all OSPF routers in a single area are configured with the same priority value, what value does a router use for the OSPF router ID in the absence of a loopback interface?

A.    the IP address of the first Fast Ethernet interface
B.    the IP address of the console management interface
C.    the highest IP address among its active interfaces
D.    the lowest IP address among its active interfaces
E.    the priority value until a loopback interface is configured

Answer: C

QUESTION 395 200-125 Dumps,200-125 Exam Questions,200-125 New Questions,200-125 VCE,200-125 PDF
The OSPF Hello protocol performs which of the following tasks? (Choose two.)

A.    It provides dynamic neighbor discovery.
B.    It detects unreachable neighbors in 90 second intervals.
C.    It maintains neighbor relationships.
D.    It negotiates correctness parameters between neighboring interfaces.
E.    It uses timers to elect the router with the fastest links as the designated router.
F.    It broadcasts hello packets throughout the internetwork to discover all routers that are running OSPF.

Answer: AC

200-125 dumps full version (PDF&VCE): https://www.lead2pass.com/200-125.html

Large amount of free 200-125 exam questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDM0s1aXlFTXBWdGM

You may also need:

100-105 exam dumps: https://drive.google.com/open?id=0B3Syig5i8gpDdDNkZEswTDRMaVE

200-105 exam dumps: https://drive.google.com/open?id=0B3Syig5i8gpDX09LZEFNYnpfM2c